Branch Switch

From FEAP Wiki
Revision as of 16:11, 13 July 2023 by S g (talk | contribs)
Jump to navigation Jump to search

Branch switch in FEAP is possible if one use arclength continuation methods. Here is a simple example. Consider a built-in column with an axial load.

feap ** Buckling Path Following with Arclength **
0 0 0 3 3 8

para
 e = 1.0
 d = 0.5
 h = 20
 pi = 4.*atan(1.)
 i  = 16.*d*d*d*d/12
 pe = pi*pi*e*i/h/h/4       ! Euler load
 p  = 0.1*pe/4/d/d          ! Reach euler load a prop value of 1


mate
 solid
  elastic moon e 0.4 0.05
  finite
  mixed

block
 cart 4 4 20*2
 1 -d -d 0
 2  d -d 0
 3  d  d 0
 4 -d  d 0
 5 -d -d h
 6  d -d h
 7  d  d h
 8 -d  d h

eboun         ! Fixed base
 3 0 1 1 1

csur          ! Pressure load (dead)
 surface
 1 -d -d h -p
 2  d -d h -p
 3  d  d h -p
 4 -d  d h -p

end

As set up the buckling load occurs according to Bernoulli-Euler theory when the load factor reaches 10. If one simply applies the load in FEAP to this level and beyond the computed solution will just be a compression of the column, though above a load of 10, FEAP will report

*D4TRIU WARNING* Sign of diagonal changed when reducing         2 equations.

due to the two lowest buckling modes. As the load increases more modes can present themselves and more equations will be reported to have sign changes during the solution process. Though FEAP detects the multiple solutions it will typically only find the unstable vertical solution. One solution to this problem is to perturb the geometry slightly so that the problem does not actually have a bifurcation point. This can be quite effective but in many cases this is not a desirable methodology. FEAP, however, provides a second method that does not require perturbing a problems definition. In order to jump onto actual bifurcation branches one can use ARCLength and the ADD feature.

The basic process is to run the load up to where the bifurcation point is thought to be. Then after solving on to the suspected unstable branch, one computes the lowest eigenvector. This is then added to the current solution and the problem is re-solved (without increasing the load). If the eigenvector points in the direction of a bifurcation solution, one will likely converge upon it. Once on the bifurcation solution, if it is stable, increases in load should stay on the new path (without the need for guidance from further eigenvectors).

With the example give above, one can perform this process with the following algorithm

batch
 opti          ! Optimize the equation ordering for the profile solver
 tplo          ! Set up time-history plots
end
arcl 1 1       ! Save the arclength parameter (load) to file
disp 1025 1    ! Save the corner x displacement
disp 1025 2    ! Save the corner y displacement
show


batch
 dt,,1
 arcl,,2         ! Initiate ARCLength
 loop,,10        ! 10 steps to get near buckling load
  time
  loop,,30
   tang,,1
  next
  plot,pview     ! Save the state for paraview plotting
 next
!
 loop,,2         ! 1 Steps using the eigen method to probe for a bifurcation path
 time            
 loop,,30
  tang,,1
 next
 iden
 subs            ! Get eigenvalues and vectors
 arcl,add,1,.1   ! Pertub onto first eigenvector hope it is the stable branch
 loop,,30        ! Re-converge
  tang,,1
 next
 plot,pview      ! Save the state for paraview plotting
 next
!
 loop,,5         ! Take 5 more steps on hopefully the stable buckling branch
  time
  loop,,30
   tang,,1
  next
  plot,pview     ! Save the state for paraview plotting
 next
end

inte

stop

Here is a comparison of the solution techniques just mentioned in terms of axial load versus transverse motion (via cross plotting the data in the files Pxxxxa.dis and Pxxxxa.arc)

BranchSwitching.png

Here is an image of the bifurcated column.

BuckCant.png

The contents of the TPLOt files show that the bifurcation initiates at load step 11 (load = 10.0828) with a bifurcation in the x-direction. At load step 12 (load = 10.0929) the column lurches to the y-direction with some x-direction motion. However at load step 13 (load = 10.0832) it stabilizes into a y-direction buckling.


Pcolumna.arc
0.0000E+00 0.0000E+00
1.0000E+00 0.0000E+00
2.0002E+00 0.0000E+00
3.0004E+00 0.0000E+00
4.0007E+00 0.0000E+00
5.0011E+00 0.0000E+00
6.0017E+00 0.0000E+00
7.0023E+00 0.0000E+00
8.0029E+00 0.0000E+00
9.0037E+00 0.0000E+00
1.0005E+01 0.0000E+00
1.0828E+01 0.0000E+00
1.0829E+01 0.0000E+00
1.0832E+01 0.0000E+00
1.0832E+01 0.0000E+00
1.0832E+01 0.0000E+00
1.0832E+01 0.0000E+00
1.0832E+01 0.0000E+00